Author Topic: turbo 1300 to turbo 2300 conversion  (Read 21535 times)

0 Members and 1 Guest are viewing this topic.

Offline dsrace

  • VIP
  • *
  • Posts: 6423
  • my one true weakness
Re: turbo 1300 to turbo 2300 conversion
« Reply #450 on: October 31, 2017, 03:37:46 PM »
they will last no doubt especially with the parts i put in it. as far as hp   really no hp goals just 30 psi boost just because i know the motor will take it lol i know one guy that put 45 psi to his, 3 times in a days ride.  it blew on the 3rd shot of 45 psi boost, through a rod. he was running stock rods and poor aftermarket forged pistons, stock crank too. i believe his was 360 hp at 20 psi boost on the dyno but don't quote me on that. if i was willing to pony up for a bo port stage III head i could jump another 75 hp maybe 100 hp with his ported head, cam and valve set up but not going to do that as i will need a diff trans before that.  a1000 puts out 90 psi max and says in the instructions that come with it but not in anyones ads!!!! ( go figure) says not to exceed 70 psi for more than 30 minutes. also says not for daily driving use. it puts out double the flow of the walbro 450 at 70 psi. walbro was either bad or not capable of flowing enough fuel efficiently to support 130lb inj's at 14 psi to 6k rpm so had to do something. seriously doubt it will make 600 hp at 30 psi boost. but that would be fun
« Last Edit: October 31, 2017, 03:55:17 PM by dsrace »
Don't never argue with an Idiot!
Because he will drag you down to his level and beat you with experience

Offline dsrace

  • VIP
  • *
  • Posts: 6423
  • my one true weakness
Re: turbo 1300 to turbo 2300 conversion
« Reply #451 on: December 09, 2017, 03:25:40 PM »
this guys video's i find very informative. i had no idea that these options existed in tuner studio/megalog hd!

« Last Edit: December 09, 2017, 03:53:01 PM by dsrace »
Don't never argue with an Idiot!
Because he will drag you down to his level and beat you with experience

Offline dsrace

  • VIP
  • *
  • Posts: 6423
  • my one true weakness
Re: turbo 1300 to turbo 2300 conversion
« Reply #452 on: December 09, 2017, 03:48:21 PM »
Don't never argue with an Idiot!
Because he will drag you down to his level and beat you with experience

Online fabr

  • Administrator
  • *
  • Posts: 91570
Re: turbo 1300 to turbo 2300 conversion
« Reply #453 on: December 09, 2017, 05:04:12 PM »
Hmmmmmm,very interesting.
"There can be no divided allegiance here.  Any man who says he is an American,
but something else also, isn't an American at all.  We have room for but one
flag, the American flag... We have room for but one language here, and that is
the English language... and we have room for but one sole loyalty and that is a
loyalty to the American people."
Theodore Roosevelt 1907

-----------------------------------------------------------
"I fear the day that technology will surpass our human interaction. The world will have a generation of idiots" Albert Einstein  (IT'S OFFICIAL THAT DAY IS HERE NOW!)

Offline dsrace

  • VIP
  • *
  • Posts: 6423
  • my one true weakness
Re: turbo 1300 to turbo 2300 conversion
« Reply #454 on: December 09, 2017, 06:00:22 PM »
i agree.......i know accel enrichment is a engine by engine tune and can be tricky but with that tutorial i believe once a person sets that graph up like .....imo should make it easier. one would hope lol the spark knock graph to tune that way i really like. his version of megalogger hd is older than mine so i`ll have to look around on that to see if any changes have been made. once the tun is closer that would be a good option.
Don't never argue with an Idiot!
Because he will drag you down to his level and beat you with experience

Offline dsrace

  • VIP
  • *
  • Posts: 6423
  • my one true weakness
Re: turbo 1300 to turbo 2300 conversion
« Reply #455 on: December 09, 2017, 06:06:15 PM »
spent countless hrs......which is meaningless as i am bored beyond for a few more weeks! but spent countless hrs searching for an online calculator or formula to convert the dead time v values from my inj data sheet into % rates as pimpxs ms3 uses % vs ms. an initial ms for base control which come to find out is based on 13.2v @100% and 43.5 flow. mine were flow tested and flowed 1139 to 1145 cc at 43.5 psi. there is a dead time voltage curve i can input this data into for a more refined control. also included is a table for small pulse width curve. so i got that data also. apperantly most pick a dead time rate based on other infor from other inj`s by many manufacturers and used that rough dead time and the default deadtime curve. then tune from that and i can see that if you dont have the info but since i`m bored and have the info i wanted to know lol
Don't never argue with an Idiot!
Because he will drag you down to his level and beat you with experience

Offline dsrace

  • VIP
  • *
  • Posts: 6423
  • my one true weakness
Re: turbo 1300 to turbo 2300 conversion
« Reply #456 on: December 09, 2017, 07:14:42 PM »
i am learning as much as i can about this system.....i'll not learn it all but still. until recently i understood injectors but did not know how important certain information was and how diff systems reference it. i have just about changed enough for cold start up that it starts at 41* so far. starts decent but a little chuggy still. from what i have read and watched in the last few days( yes days!lol) i have learned that if the inj dead times are close it can be tuned accordingly but if they are off enough it will effect idle and both cold and hot restart. now that is still not off to far in dead time ms as in 1.50 compared to should be 1.20. in my case we entered 1.2 ms and fuel injector development (fid) says my actual dead time for my inj's is 1.03 @13.2v based on 43.5 psi base. asked this question every way i could think of on stingers site and could not get a  straight answer from a certain guy and no response from another and they sell both the ms3 and inj's and know the data sheets don't show up in the format they need to for the ecu's they sell! the instructions they send for start up leave a lot to be desired as well. found some posts in 2 diff forums....one says to multi or divide ms# by 64 to get % or divide % by to get ms#. i don't have enough of a graph to verify that but rounded up to the nearest hundredths it's really close. the only other reference i could find was to multiply ms by 1100 and use the first 3 digits.......sound safe?? amazingly it works rounded up again but only on two points of my graph. my alternator is rock solid while the engine is running, but batt drops to 10 ish v's while cranking so that dead time voltage correction curve helps compensate but based on a % rather than ms rate to compensate for more sluggish response times. now that coupled with the fact that i never adjusted ms3 voltage reading to match my batt gauge, volt meter reading at batt and power point at fuse block , adds to the issue. it was off by .2 volts. not huge but again throws voltage correction curve off a bit. my base ms dead time is set at 1.2 and should be 1.03 so will change the tune changing that setting along with entering correct info into volt corr curve.     it all takes time and depends on how precise one wants to get i guess but if i have the info i might as well make use of it!
Don't never argue with an Idiot!
Because he will drag you down to his level and beat you with experience

Offline dsrace

  • VIP
  • *
  • Posts: 6423
  • my one true weakness
Re: turbo 1300 to turbo 2300 conversion
« Reply #457 on: December 09, 2017, 08:00:18 PM »
pics of TS section and of what the inj data sheet is and what fid recalculated to







Don't never argue with an Idiot!
Because he will drag you down to his level and beat you with experience

Offline dsrace

  • VIP
  • *
  • Posts: 6423
  • my one true weakness
Don't never argue with an Idiot!
Because he will drag you down to his level and beat you with experience

Online fabr

  • Administrator
  • *
  • Posts: 91570
Re: turbo 1300 to turbo 2300 conversion
« Reply #459 on: January 10, 2018, 07:51:43 PM »
IIRC my Meziere is 3KW.  It spins my 14:1 like I left the plugs out.   :m
"There can be no divided allegiance here.  Any man who says he is an American,
but something else also, isn't an American at all.  We have room for but one
flag, the American flag... We have room for but one language here, and that is
the English language... and we have room for but one sole loyalty and that is a
loyalty to the American people."
Theodore Roosevelt 1907

-----------------------------------------------------------
"I fear the day that technology will surpass our human interaction. The world will have a generation of idiots" Albert Einstein  (IT'S OFFICIAL THAT DAY IS HERE NOW!)

Offline dsrace

  • VIP
  • *
  • Posts: 6423
  • my one true weakness
Re: turbo 1300 to turbo 2300 conversion
« Reply #460 on: January 10, 2018, 08:02:38 PM »
 well if i had that option i would lol hightq makes a 2kw model but its expensive!
Don't never argue with an Idiot!
Because he will drag you down to his level and beat you with experience

Online fabr

  • Administrator
  • *
  • Posts: 91570
Re: turbo 1300 to turbo 2300 conversion
« Reply #461 on: January 10, 2018, 08:47:35 PM »
We don't even want to talk price of the Meziere.......................... Sort of the old saying,if ya gotta ask how much you don't need it. Or in my case,I had zero other options.  AND I had to modify the damn thing as well.  5: Talk about adding insult to $$injury. Oh well. :nw
"There can be no divided allegiance here.  Any man who says he is an American,
but something else also, isn't an American at all.  We have room for but one
flag, the American flag... We have room for but one language here, and that is
the English language... and we have room for but one sole loyalty and that is a
loyalty to the American people."
Theodore Roosevelt 1907

-----------------------------------------------------------
"I fear the day that technology will surpass our human interaction. The world will have a generation of idiots" Albert Einstein  (IT'S OFFICIAL THAT DAY IS HERE NOW!)