DTSFab.com (Desert, Trail and Sand)

Automotive Powered Off Road (AKA: Buggys, Jeeps, Trucks, Etc,Etc. ) => Motor and Drivetrain => Topic started by: dsrace on February 02, 2010, 09:12:33 PM

Title: 930 cv external greaser's
Post by: dsrace on February 02, 2010, 09:12:33 PM: http://www.pacificcustoms.com/AC501930GR.html (http://www.pacificcustoms.com/AC501930GR.html)

thought some of you might like these!
Title: Re: 930 cv external greaser's
Post by: Carlriddle on February 03, 2010, 06:11:45 AM: $106 per side thumb down and I bet you couldn't put them in most setups without redoing something in driveline. They gotta be about 1/2" wide.
Title: Re: 930 cv external greaser's
Post by: fabr on February 03, 2010, 06:55:34 AM: 106 per side is cheap,relatively speaking, in the light of of maintenance hassles otherwise. On the other hand ,many of us do not need to maintain the cv's nearly every trip out like many larger cars do.
Title: Re: 930 cv external greaser's
Post by: dsrace on February 03, 2010, 01:00:47 PM: I see where this would be a very nice option myself and i am going to buy a set but yes kind of pricy! I did call a little while ago and asked them to measure one to see what kind of standoff it has, he used a tape measure and said 7/16".
Title: Re: 930 cv external greaser's
Post by: Enemy on February 03, 2010, 05:20:33 PM: Quote from: Dsrace on February 03, 2010, 01:00:47 PM
I see where this would be a very nice option myself and i am going to buy a set but yes kind of pricy! I did call a little while ago and asked them to measure one to see what kind of standoff it has, he used a tape measure and said 7/16".

Yep, when a guy lets out a slight whimper before removing the boot of a CV joint (like DS does), I can see why you would say this would be a very nice option... ;D ;D ;D
Title: Re: 930 cv external greaser's
Post by: Doug Heim on February 03, 2010, 05:26:14 PM: I agree that they are a nice option as I whimper as well
Title: Re: 930 cv external greaser's
Post by: dsrace on February 03, 2010, 09:29:30 PM: I hate cv's just for that reason! the greasy mess is just well there aren't words to describe it :'( :'( I am going to give these new high anlge non plung 930's a try though! If I can give them a couple of pumps of grease every couple of days on the dunes and then squeeze the boots like a tube of toothpaste to get a little out I will be happy! ;) glen I was looking at a non plunge cv tonight trying to decide if the 7/16" standoff would be enough clearance on my 930 flat flange for the cv to pivot and the 1/8" axle plunge I am using, I think it would be damn close. I might just have to buy a pair and use them at the transaxle after shipping them to the worlds best machinist to have a pair made with 3/4" standoff!!! ;) ;) this way I can go back to the u-j's when ever I want! ;D ;D
Title: Re: 930 cv external greaser's
Post by: Enemy on February 04, 2010, 05:31:35 PM: See? 3 Whimpers. rofl

It is a damn nice idea DS!
Title: Re: 930 cv external greaser's
Post by: Doug Heim on February 04, 2010, 05:54:11 PM: who the hell is this damn great machinist that you know of? I may be the best in 3 counties, but not the world LMAO
Title: Re: 930 cv external greaser's
Post by: dsrace on February 04, 2010, 07:52:35 PM: I can't remember his name but he says youbetcha alot! ;D and is a damn good artists when it comes to road painting! rofl rofl you even had me for a few seconds as I was parked behind the park ranger watching him scratch his head ;D
Title: Re: 930 cv external greaser's
Post by: Enemy on February 04, 2010, 08:01:26 PM: I need to test this "machinist" of yers out DS, for i got a fun job for him!

Lu-Lu has spoken dont-cha-know!
Title: Re: 930 cv external greaser's
Post by: Doug Heim on February 04, 2010, 08:30:41 PM: Aww Christ hey! LMAO LMAO LMAO rofl rofl rofl
Title: Re: 930 cv external greaser's
Post by: fabr on February 04, 2010, 09:20:04 PM: ;D ;D ;D ;D ;D ;D ;D ;D rofl rofl rofl rofl rofl rofl