0 Members and 1 Guest are viewing this topic.
were is the group camping at. the dates ?
I am Cowboy camp along with a few others. Fabr is at Duece's. My dates there are 5/2 thru 5/6, heading home Sunday.
Well,, I test ran the car in the sand. pulled hard in all four gear to 7000rpm. I will say, it is lacking in the low end. but when the boost comes in, its time to hold on and hit the next gear. I'm not sure, if I lost a vacuum line or what! but all of a sudden it limits the rpms to 3000rpm. it has temp. protection on warm up and over temp. but I do not thank it is this. I let the car cool down for a few hours and it is still limiting it to 3000rpm. I have not looked at the vacuum/ boost reference lines yet. but it seem like it is limiting it, right as I start making boost. any thought??
I had to drive my 2.0 like a 2 stroke. You will learn to throttle before you hit a hill or incline to build boost. What plug gap do you have? I had that same issue with mine when I first got it and it was just plugs. I change mine every season and keep plenty handy. If the gap is too big the turbo will blow the spark out. I set mine to .025.
New plugs ( NKG R5671A-7 ) put in at the dyno. internet said out of the box .032gap. looks like I my try regaping them. factory said .025.
I put a fresh set in my new motor at .035 out of the box. They ran great all weekend and on my last ride would not rev over 4k. I threw fresh plugs in at .025 in when I got home and ran perfect. I was running NGK but now run standard Autolite plugs per recommendation from a local builder. The Autolite is copper core and has a shorter ground electrode that makes it more square to the positive electrode. I will get the numbers tonight. And I ALWAYS check plug gaps cause they are not always correct out of the box.
I'M WITH YOU ON CHECKING THE PLUG GAP, OUT OF THE BOX. BUT, I DID NOT WANT TO STEP ON THE TUNERS TOES. WE HAD ALLREADY HAD A FEW HEATED WORDS, BY THIS POINT. BUT THIS IS GOOD TO HERE. IT WILL BE THE FIRST THING I TRY. THANKS FOR THE INPUT. NOT YELLING. I HAVE TO TYPE EVRYTHING IN CAPS AT WORK. ITS A HARD HABBIT TO BREAK. LOL I WOULD LIKE TO KNOW WHAT PLUG YOUR RUNING NOW WHEN YOU HAVE TIME.
http://www.glamisdunes.com/invision/index.php?/forums/topic/301856-spark-plugs-for-subaru-ej20-20-turbo/#comment-4615082In case ya just want to read here John:I never use iridium nor platinum on my engines, these plugs are designed to go 50k miles in a street car at near 14.7 to 1 AFR, they can last there like that. when they are in a dune buggy with a lot richer tune they could foul and not recover. go with the copper NGK that have been recommended.sometimes cheaper is better!!! Esco said: azcg said: Getting ready to change the plugs in my stock Subie 2.0 turbo running 6 psi of boost on 91 octane.Many of the Subaru forums vary about what's best. NGK BKR6EIX (Iridium) or NGK BKR6-11 (Copper) NGK PFR6G (Platinum) seem the most common. But there's also talk of using one range colder NGK BKR7.What are other members experience with their 2.0 motors?I use these in mine NGK-ZFR6F-11 Copper core V powerI also use the NGK-ZFR6F-11, gap to 0.020 replace every season.The plugs come pre-gapped to 0.030 or so, so you have bend the tip down a lot to get 0.020 and the tip will not be parallel with the electrode. You can try gapping to 0.025 or 0.030. When gapped that big I got miss fires under boast, felt like a rev limiter at higher RPMs.The gap gets wider with use, so gap to 0.020 now and at the end of the season it will be bigger. Keeping running them and it will misfire under boost.Sounds like your description.
i know you said you tried re gapping but did you try a new set gapped correctly for you boost level? the old ones my be damaged internally at this point.