Recent Posts

Pages: [1] 2 3 4 5 6 ... 10
1
Group Gatherings/Special Events / Re: St Anthony's Idaho Aug 5-9 2024 Group Ride Days
« Last post by Enemy on February 27, 2024, 09:28:20 PM »
I still plan on going, but I just have a few hurdles.  Putting a new engine together now (or the clean up stage really).  New dual BB turbo, oh yea baby.   8)  So that one will be sorted.  I'll make it   :nw

Same boat here, except for the new motor.. and turbo.. But I got a new header!
Beat the shit out of it by the Platte yesterday then did a re-torque on the hot stuff, need to make a couple new exhaust mounts and should be dialed.

2
JOKES Central / Re: Soooo true
« Last post by Enemy on February 27, 2024, 09:22:02 PM »
That is what they will do when finished with it!
This phucker was installed to make the destruction of the country look like senile incompetence.
Obamma and big mike's third term..
3
JOKES Central / Re: Soooo true
« Last post by Generalg on February 27, 2024, 09:40:37 AM »
4
JOKES Central / Re: Soooo true
« Last post by fabr on February 23, 2024, 06:03:46 PM »
If only............3 years ago.
5
JOKES Central / Soooo true
« Last post by dsrace on February 23, 2024, 04:26:32 PM »


6
Group Gatherings/Special Events / Re: St Anthony's Idaho Aug 5-9 2024 Group Ride Days
« Last post by Generalg on February 23, 2024, 07:10:25 AM »
Welllllll,at least I won't be the lone ranger. Should be a good time general.

You bet it will be a good time!  See you all in May at LS as well.
7
Motor and Drivetrain / Re: I want it i need it.....its time
« Last post by dsrace on February 22, 2024, 07:48:39 PM »
The vast majority are fabbed aluminum tanks. There has been waaayyyyyy toooooo many people burned or killed having fun. I don't plan on being one of them. Anything CAN happen but I have taken care to hopefully avoid it. Nothing other than PEX bladders or true fuel cell bladders for me. It's just not worth the risk,IMO.  After what happened to your "fuel cell" last time I shudder to think how lucky you were. I'll stop pestering you about it now ,it's your skin.

Not once but twice in 2 days! And the pos cable was loose an arcing!! Guardian angel comes to mind!! Mine will be a lined tank, no doubts there, just which direction is in the air.



So only had a couple hrs to re work the rear a arm design. Do no tie rods and shallowness beds possible. The upper at wheel will be 7/8", not 3/4" as pictured.

Remember, I cut my olds ones up for mock up pieces so no critiquing  the roughness  :m







8
Motor and Drivetrain / Re: I want it i need it.....its time
« Last post by fabr on February 22, 2024, 05:37:25 PM »
The vast majority are fabbed aluminum tanks. There has been waaayyyyyy toooooo many people burned or killed having fun. I don't plan on being one of them. Anything CAN happen but I have taken care to hopefully avoid it. Nothing other than PEX bladders or true fuel cell bladders for me. It's just not worth the risk,IMO.  After what happened to your "fuel cell" last time I shudder to think how lucky you were. I'll stop pestering you about it now ,it's your skin.
9
Group Gatherings/Special Events / Re: St Anthony's Idaho Aug 5-9 2024 Group Ride Days
« Last post by fabr on February 22, 2024, 05:25:05 PM »
Welllllll,at least I won't be the lone ranger. Should be a good time general.
10
Motor and Drivetrain / Re: I want it i need it.....its time
« Last post by dsrace on February 22, 2024, 10:10:26 AM »
I  mentioned this because I have been questioning runnng both on the bottom arm. They worked well on the last build and I am not light weight. That was one on bottom and top of a 4 point mount. I assumed with that design that the solid fronts overlapping the mini tie rod rears would be offset enough to add some strength. The shock mounted to the front side of the. A arm too. So either I do that again or I go single heim only. 


Btw, I was finally contacted by a mod ad gd.com. they had to personally reset my acct. Not sure why, don't care,  but did read that post.  That post is also on sand asylum on fb. The owner/drivers hasn't stated exactly what cause the fire but 2 friends have stated his fuel tank was just a welded aluminum tank, no bladder. 
Pages: [1] 2 3 4 5 6 ... 10
SimplePortal 2.3.7 © 2008-2024, SimplePortal