Recent Posts

Pages: 1 2 3 4 [5] 6 7 8 9 10
41
Motor and Drivetrain / Re: Flex Fuel Sensor Hmmmmm?
« Last post by fabr on December 06, 2018, 08:09:53 PM »
That was from the place in Benson you asked me about.
42
Motor and Drivetrain / Re: Flex Fuel Sensor Hmmmmm?
« Last post by dsrace on December 06, 2018, 07:35:23 PM »
i have not heard back from patrick yet so i will be calling tomorrow.
43
Motor and Drivetrain / Re: Flex Fuel Sensor Hmmmmm?
« Last post by fabr on December 06, 2018, 07:16:33 PM »
Today ,from my original supplier. DAMN!!

Good morning, at this time I am not able to sell any fuel to anyone without a
Minnesota address.  I am working on a solution but running into roadblocks in every
state.  If there comes a time when I can start to distribute again I will post it on
our website which is www.glacialplains.com.

Thank you,


Shaun Stottler
Energy Division Manager
Glacial Plains Coop
320-842-5311
www.glacialplains.com

44
UTV Member Project Logs / Re: AR-51 build
« Last post by fabr on December 06, 2018, 06:41:12 PM »
Welllll,it's honest.
45
Everything Fabrication / Re: ABS Vacumn Forming
« Last post by dsrace on December 06, 2018, 03:45:48 PM »
 :nw gg:
46
UTV Member Project Logs / Re: AR-51 build
« Last post by dsrace on December 06, 2018, 03:45:09 PM »
Carl sucks lately w buggy stuff.  LOL  Its cold/winter and buggy is packed in trailer.

But the new Bazzaz sys, is e-85 compatible with a newer O2 sensor.  I have my maps setup to e65 I believe with this turbo zx12.  Larger injectors 500cc, stock 330cc. 
Bit of learning curve with turbo e85 maps for me.  Its getting there.

that's your review??  rofl rofl
47
Everything Fabrication / Re: ABS Vacumn Forming
« Last post by fabr on December 06, 2018, 02:47:52 PM »
With some preliminary experimentation I think I will try to get the ABS to 375F.  Also am going to make first pull with .065 material.
48
Everything Fabrication / Re: ABS Vacumn Forming
« Last post by fabr on December 06, 2018, 02:44:58 PM »
Sparks,I also am most concerned with the cup holders. Pretty deep and close together. I do have 8 vac ports around the bottom of each. .125 is pretty thick for it but we'll see.
49
Everything Fabrication / Re: ABS Vacumn Forming
« Last post by wightsparks on December 06, 2018, 10:53:51 AM »
Looks good. I haven't done ABS vac forming since school - cough-ahem years ago. Will be interested to see if those cup holder form.
50
UTV Member Project Logs / Re: AR-51 build
« Last post by Carlriddle on December 06, 2018, 10:26:05 AM »
Carl sucks lately w buggy stuff.  LOL  Its cold/winter and buggy is packed in trailer.

But the new Bazzaz sys, is e-85 compatible with a newer O2 sensor.  I have my maps setup to e65 I believe with this turbo zx12.  Larger injectors 500cc, stock 330cc. 
Bit of learning curve with turbo e85 maps for me.  Its getting there.
Pages: 1 2 3 4 [5] 6 7 8 9 10