DTSFab.com (Desert, Trail and Sand)

UTV's Off Road ( RZR, YXZ, Mini Buggy, Carts,etc.) => UTV General Discussion => Topic started by: Wyattboche on September 22, 2010, 12:45:46 PM

Title: banjo fittings
Post by: Wyattboche on September 22, 2010, 12:45:46 PM: I'm in need of some banjo fittings that have ether 1/4" on the end or accept An fitting. Anyone know where I can find such a apart?
Title: Re: banjo fittings
Post by: Wyattboche on September 22, 2010, 12:52:36 PM: nevermind. found some
http://www.jegs.com/webapp/wcs/stores/servlet/KeywordSearchCmd?storeId=10001&catalogId=10002&langId=-1&N=0&Ntk=all&Jnar=0&Ne=1%2B2%2B3%2B13%2B1147708&searchTerm=banjo+fittings (http://www.jegs.com/webapp/wcs/stores/servlet/KeywordSearchCmd?storeId=10001&catalogId=10002&langId=-1&N=0&Ntk=all&Jnar=0&Ne=1%2B2%2B3%2B13%2B1147708&searchTerm=banjo+fittings)
Title: Re: banjo fittings
Post by: Wyattboche on September 22, 2010, 01:02:12 PM: Can you make your own brake lines using stainless braided rubber hose? can you use this?

http://www.jegs.com/webapp/wcs/stores/servlet/KeywordSearchCmd?storeId=10001&catalogId=10002&langId=-1&N=0&Ntk=all&Jnar=0&Ne=1%2B2%2B3%2B13%2B1147708&searchTerm=555-100900 (http://www.jegs.com/webapp/wcs/stores/servlet/KeywordSearchCmd?storeId=10001&catalogId=10002&langId=-1&N=0&Ntk=all&Jnar=0&Ne=1%2B2%2B3%2B13%2B1147708&searchTerm=555-100900)
Title: Re: banjo fittings
Post by: SPEC on September 23, 2010, 05:07:16 AM: I didn't see a psi. rating
So prolly no
Title: Re: banjo fittings
Post by: LiveWire on September 23, 2010, 11:24:56 AM: I can get you custom braided stainless brake lines with the ends crimped on. Nearly any fitting. I need a length defined as like center of banjo to whatever. You need the banjo bolt with the fitting to make sure the hole lines up with the internal groove. So I would need the thread of the bolt. You can email sales@aftershockmotorsports.com. I want to get a page up that lets you build the line online, but it will take a while.
Title: Re: banjo fittings
Post by: Wyattboche on September 23, 2010, 11:55:13 AM: Quote from: LiveWire on September 23, 2010, 11:24:56 AM
I can get you custom braided stainless brake lines with the ends crimped on. Nearly any fitting. I need a length defined as like center of banjo to whatever. You need the banjo bolt with the fitting to make sure the hole lines up with the internal groove. So I would need the thread of the bolt. You can email sales@aftershockmotorsports.com. I want to get a page up that lets you build the line online, but it will take a while.
What sizes do you have? I'm in the process of making my own rear disc conversion for my 04 honda rubicon.
(https://dtsfab.com/proxy.php?request=http%3A%2F%2Fi293.photobucket.com%2Falbums%2Fmm73%2Fwyattboche%2Fhondareardisckitpic.jpg&hash=e50045df98fb81eb2fc1bf12cb5ee5d3f8ffc2cf)
Trying to fiqure if I wanta handle bar brake lever or the right foot brake?If I can find a left side master and or a master foot pedal
Title: Re: banjo fittings
Post by: Wyattboche on September 23, 2010, 11:57:28 AM: Quote from: LiveWire on September 23, 2010, 11:24:56 AM
I can get you custom braided stainless brake lines with the ends crimped on. Nearly any fitting. I need a length defined as like center of banjo to whatever. You need the banjo bolt with the fitting to make sure the hole lines up with the internal groove. So I would need the thread of the bolt. You can email sales@aftershockmotorsports.com. I want to get a page up that lets you build the line online, but it will take a while.
Maybe you should be a sponsor and have your own page on dtsf? Just a thought. then you could post what you have available.
Title: Re: banjo fittings
Post by: SPEC on September 23, 2010, 12:03:20 PM: Measure it up Wyatt I still have a drawer full of atv Brake stuff From building the 460's
Title: Re: banjo fittings
Post by: Wyattboche on September 23, 2010, 12:16:13 PM: Quote from: Spec on September 23, 2010, 12:03:20 PM
Measure it up Wyatt I still have a drawer full of atv Brake stuff From building the 460's
What brand are they from? Are they honda brand or ?
Title: Re: banjo fittings
Post by: SPEC on September 23, 2010, 12:26:49 PM: Quote from: Wyattboche on September 23, 2010, 12:16:13 PM
What brand are they from? Are they honda brand or ?

I haven't looked lately...But from honda, yamamhhhhhaahahahahahaha, and some custom ones I had the parts store whip up...Prolly some polaris too
Title: Re: banjo fittings
Post by: Wyattboche on September 23, 2010, 12:35:49 PM: Anyone buy a wrecked rc-51 bike and have a front clutch master cylinder for sale?
Title: Re: banjo fittings
Post by: Wyattboche on December 12, 2010, 09:28:29 PM: Does anyone know where I can find a tip over valve for a fuel cell? Needs to be -6AN
Title: Re: banjo fittings
Post by: LiveWire on December 13, 2010, 12:07:24 PM: Quote from: Wyattboche on September 23, 2010, 11:57:28 AM
Maybe you should be a sponsor and have your own page on dtsf? Just a thought. then you could post what you have available.

I am allowed to post what I have.

I can make custom lines with nearly any fitting you need.

Other stuff is anything Wilwood, anything EMPI, Rod End Supply, Comet/CPA.

The caliper in the picture is a Wilwwod PS1. http://aftershockmotorsports.com/cart/index.php?main_page=product_info&cPath=36_37&products_id=62

I have a pair of rotors that mounting pattern as well.